Faw 25 Tons Dumper Truck (CA3257)

Faw 25 Tons Dumper Truck (CA3257)
Clutch
--Dry single Φ 430mm plate
--Diaphragm spring
--Hydraulic control with air assist
--Non-asbestos composite friction material

Transmission
--Shanxi Fuller 9JS135 mechanical transmission with auxiliary case, 9 forward speeds and 1 reverse (CA6DL1-28 only)
--Ratios: 1st 12.11, 2ND 8.08, 3rd 5.93, 4th 4.42, 5th 3.36, 6th 2.41, 7th 1.76, 8th 1.32, 9th 1.00, Rev. 12.66
--Shanxi Fuller 8JS118 mechanical transmission with auxiliary case, 8 forward speeds and 1 reverse (CA6DL1-26 only)
--Ratios: 1st 11.40, 2ND 7.94, 3rd 5.63, 4th 4.06, 5th 2.81, 6th 1.96, 7th 1.39, 8th 1.00, Rev. 11.35

Front axle
--Drop forged "I" beam, rear mounted tie rod
--Rated axle capacity: 7000 kg
--Integral power steering, tilt and telescopic steering column
--Suspension: Semi-elliptic multi-leaf springs with telescopic double acting shock absorbers
--8.00V-20 steel disc wheels and 11.00-20-16PR tires (Single, bias tube-type)

Rear axle
--457 cast axle, 5.286 ratio, full-floating
--Rated axle capacity: 23000 kg
--Suspension: Balance spring, semi-elliptic multi-leaf
--8.00V-20 steel disc wheels and 11.00-20-16PR tires (Dual, bias tube-type)

Brake
--Front and rear dual-circuit independent air brake system with air dryer
--Reservoirs: Four 35L steel reservoirs and one 15L steel reservoir
--Service brakes: Air actuated, drum type, brake drum inner diameter: 400mm
--Brake shoe width: Front 135mm, rear 200mm
--Parking brake: Pneumatically controlled spring brakes, operated by manually actuated valve in conjunction with quick
Release valve, acting on rear wheels
--Exhaust brake: Electrically controlled, pneumatically activated butterfly valve in exhaust pipe

frame
--Ladder type, channel section side rails
--Cross section dimensions: 280× 90× 8mm (with 5mm inner reinforcement)
--Assembled width: 865mm in the front and rear

Body
--Dump - fully welded, latching tailgate, integral splash guards, cab shield

Electrical system
--24 Volt, negative ground system
--Battery: 6-QAW-180D, capacity: 2× 180A. H
--Combination halogen headlamps/marker lamps
--Combination stop, tail and back-up lamps with reflector

Weights (kg)
--Curb weight: 15800
--Front dual axle curb weight: 5950
--Rear dual axle curb weight: 9850
--Load capacity: 20000

Dimensions (mm)
--Overall dimensions (length × Width × Height): 10115× 2490× 2730
--Body inner dimensions (length × Width × Height): 7200× 2300× 1400
--Track (front/rear): 1944/1847
--Wheelbase: 1900+3650+1350
--Front overhang: 1375
--Back of cab to tandem axle center: 5285
--Rear axle center to end of frame: 1085

Payload Capacity (kg)13, 800
Front Axle Curb Weight (kg) (with body)4, 325
Rear Axle Curb Weight (kg) (with body)7, 875
Total Curb Weight (kg) (with body)12, 200
Front GAW (gross axle weight) (kg)7, 000
Rear GAW (kg)19, 000

Model	CA6DF2-26	CA6DF2-24
Type	6-cylinder in line, 4-stroke, water-cooled, direct injection, turbocharged, air-to-air intercooled
Peak Power kW (HP) @ RPM	192(260) @ 2300	177(240) @ 2300
Max Torque N. m (lb. ft. ) @ RPM	930 @ 1400	890 @ 1400
Specific Fuel Consumption (g/kWh)	205
Bore & Stroke (mm)	110× 125
Displacement (L)	7.127
Compression Ratio	17: 1
Emissions Rating	Euro 2	Euro 2
Air Compressor	380L/min @ 2300rpm
Lube Oil System	Full flow oil filter, centrifugal oil filter, turbocharger oil filter
Starting System	Starter: 24V 6kW Alternator: 28V 1.5kW, with built-in regulator Cold starting aid: grid-type pre-heater
Air Intake System	Dual paper element air filter with air restriction indicator
Exhaust System	Horizontal muffler with flexible pipe
Fuel Supply System	One frame-mounted primary fuel filter and two engine-mounted secondary fuel filters
Fuel Tank Capacity	200L
Cooling System	Radiator: tube-type aluminum radiator with coolant recovery tank Fan: Lightweight plastic with viscous type drive